Re: QNAP 219 P II, Luks, Debian

["Li, Peng" <peng.li@f2f10.com>]

On 2014-09-07 11:35, Ian Campbell wrote:
> On Fri, 2014-09-05 at 10:49 -0400, Li, Peng wrote:
> > Here's dmesg out put. Let me know whether there's info you are looking
> > for.
>
> It's what I asked for but not actually what I wanted, sorry.
>
> What meant to ask for was the serial console log, i.e. with all the
> output from the userspace tools running from the initramfs.
>
> The dmesg only includes the kernel messages and I'm reasonably sure 
> it's
> not a kernel level issue.
>
> Sorry again.
>
> Ian.
Hi Ian,

Thanks for looking into this. Here's a console log captured by putty.

Let me know if this helps.
thanks
peng


         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** LOADER **
 ** MARVELL BOARD: DB-88F6282A-BP LE TS-219P2+ ,PHY=1.8v

U-Boot 1.1.4 (Jan  3 2012 - 14:49:37) Marvell version: 3.5.3

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CD5C0

Soc: MV88F6282 Rev 1CPU running @ 2000Mhz L2 running @ 500Mhz
SysClock = 500Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000   size 256MB
DRAM CS[1] base 0x10000000   size 256MB
DRAM Total size 512MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
[16384kB@f8000000] Flash: 16 MB

CPU : Marvell Feroceon (Rev 1)
USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
PEX 1: PCI Express Root Complex Interface
PEX interface detected Link X1

Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 1 0]: Enable DMA mode (5)
  Device 1 @ 0 1:
Model: ST1000DM003-9YN162                       Firm: HP13     Ser#: 
S1D1NX7L
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)

Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  1  0
Send Cmd : 0x68 to UART1
## Booting image at 00800000 ...
   Image Name:   kernel 3.2.0-4-kirkwood
   Created:      2014-09-01  15:51:28 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1612040 Bytes =  1.5 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.2.0-4-kirkwood 
(debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-14) ) 
#1 Debian 3.2.60-1+deb7u3
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), 
cr=00053977
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: QNAP TS-119/TS-219
[    0.000000] Ignoring unrecognised tag 0x41000403
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  
Total pages: 130048
[    0.000000] Kernel command line: console=ttyS0,115200 
root=/dev/mapper/VG01-LVG01 initrd=0xa00000,0x900000 ramdisk=34816
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 
bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 
bytes)
[    0.000000] Memory: 512MB = 512MB total
[    0.000000] Memory: 505756k/505756k available, 18532k reserved, 0K 
highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xe0800000 - 0xfe800000   ( 480 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xe0000000   ( 512 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc03e85dc   (3970 kB)
[    0.000000]       .init : 0xc03e9000 - 0xc040d000   ( 144 kB)
[    0.000000]       .data : 0xc040e000 - 0xc0448900   ( 235 kB)
[    0.000000]        .bss : 0xc0448924 - 0xc04abfb8   ( 398 kB)
[    0.000000] NR_IRQS:114
[    0.000000] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps 
every 21474ms
[    0.000000] Console: colour dummy device 80x30
[    7.637384] Calibrating delay loop... 1980.82 BogoMIPS (lpj=9904128)
[    7.697285] pid_max: default: 32768 minimum: 301
[    7.697372] Security Framework initialized
[    7.697425] Mount-cache hash table entries: 512
[    7.697685] Initializing cgroup subsys cpuacct
[    7.697703] Initializing cgroup subsys memory
[    7.697721] Initializing cgroup subsys devices
[    7.697728] Initializing cgroup subsys freezer
[    7.697733] Initializing cgroup subsys net_cls
[    7.697737] Initializing cgroup subsys blkio
[    7.697752] Initializing cgroup subsys perf_event
[    7.697818] CPU: Testing write buffer coherency: ok
[    7.698793] devtmpfs: initialized
[    7.700095] print_constraints: dummy:
[    7.700282] NET: Registered protocol family 16
[    7.700867] Kirkwood: MV88F6282-Rev-A1, TCLK=200000000.
[    7.700877] Feroceon L2: Enabling L2
[    7.700903] Feroceon L2: Cache support initialised.
[    7.701777] Kirkwood PCIe port 0:
[    7.701781] link up
[    7.701785] Kirkwood PCIe port 1:
[    7.701788] link up
[    7.701792] PCI: bus0 uses PCIe port 0
[    7.702290] PCI: bus0: Fast back to back transfers disabled
[    7.702503] PCI: bus1 uses PCIe port 1
[    7.702835] PCI: bus1: Fast back to back transfers disabled
[    7.703004] pci 0000:01:01.0: BAR 0: assigned [mem 
0xe8000000-0xe8007fff 64bit]
[    7.703024] pci 0000:00:01.0: BAR 6: assigned [mem 
0xe0000000-0xe000ffff pref]
[    7.703033] pci 0000:00:01.0: BAR 5: assigned [mem 
0xe0010000-0xe0011fff]
[    7.703042] pci 0000:00:01.1: BAR 4: assigned [io  0x1000-0x100f]
[    7.703052] pci 0000:00:01.1: BAR 0: assigned [io  0x1010-0x1017]
[    7.703062] pci 0000:00:01.1: BAR 2: assigned [io  0x1018-0x101f]
[    7.703071] pci 0000:00:01.1: BAR 1: assigned [io  0x1020-0x1023]
[    7.703081] pci 0000:00:01.1: BAR 3: assigned [io  0x1024-0x1027]
[    7.704240] bio: create slab <bio-0> at 0
[    7.704525] vgaarb: loaded
[    7.704905] Switching to clocksource orion_clocksource
[    7.714938] NET: Registered protocol family 2
[    7.715072] IP route cache hash table entries: 4096 (order: 2, 16384 
bytes)
[    7.715476] TCP established hash table entries: 16384 (order: 5, 
131072 bytes)
[    7.715856] TCP bind hash table entries: 16384 (order: 4, 65536 
bytes)
[    7.716048] TCP: Hash tables configured (established 16384 bind 
16384)
[    7.716053] TCP reno registered
[    7.716060] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    7.716078] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    7.716226] NET: Registered protocol family 1
[    7.716423] Unpacking initramfs...
[    7.997059] Freeing initrd memory: 9216K
[    7.997072] NetWinder Floating Point Emulator V0.97 (double 
precision)
[    7.997488] audit: initializing netlink socket (disabled)
[    7.997521] type=2000 audit(0.350:1): initialized
[    7.998379] VFS: Disk quotas dquot_6.5.2
[    7.998438] Dquot-cache hash table entries: 1024 (order 0, 4096 
bytes)
[    7.998511] JFFS2 version 2.2. (NAND) (SUMMARY)  \A9 2001-2006 Red 
Hat, Inc.
[    7.998734] msgmni has been set to 1005
[    7.999810] alg: No test for stdrng (krng)
[    7.999891] Block layer SCSI generic (bsg) driver version 0.4 loaded 
(major 253)
[    7.999900] io scheduler noop registered
[    7.999905] io scheduler deadline registered
[    7.999939] io scheduler cfq registered (default)
[    8.000018] mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
[    8.000039] mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
[    8.034947] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[    8.074945] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
[    8.114945] mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
[    8.154944] mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
[    8.155191] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    8.175513] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 
16550A
[    8.685899] console [ttyS0] enabled
[    8.709531] serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 
16550A
[    8.717424] m25p80 spi0.0: m25p128 (16384 Kbytes)
[    8.722152] Creating 6 MTD partitions on "spi_flash":
[    8.727249] 0x000000000000-0x000000080000 : "U-Boot"
[    8.732807] 0x000000200000-0x000000400000 : "Kernel"
[    8.738374] 0x000000400000-0x000000d00000 : "RootFS1"
[    8.743991] 0x000000d00000-0x000001000000 : "RootFS2"
[    8.749644] 0x000000080000-0x0000000c0000 : "U-Boot Config"
[    8.755827] 0x0000000c0000-0x000000200000 : "NAS Config"
[    8.761885] mousedev: PS/2 mouse device common for all mice
[    9.774940] rtc-mv rtc-mv: internal RTC not ticking
[    9.779908] i2c /dev entries driver
[    9.786878] rtc-s35390a 0-0030: rtc core: registered rtc-s35390a as 
rtc0
[    9.793675] cpuidle: using governor ladder
[    9.797846] cpuidle: using governor menu
[    9.802253] TCP cubic registered
[    9.805510] NET: Registered protocol family 17
[    9.809976] Registering the dns_resolver key type
[    9.815033] registered taskstats version 1
[    9.820093] rtc-s35390a 0-0030: setting system clock to 2014-09-07 
22:33:10 UTC (1410129190)
[    9.828610] Initializing network drop monitor service
[    9.834288] Freeing init memory: 144K
Loading, please wait...
[    9.885362] udevd[51]: starting version 175
[   10.062521] SCSI subsystem initialized
[   10.140601] sata_mv sata_mv.0: slots 32 ports 2
[   10.149365] scsi0 : sata_mv
[   10.152668] scsi1 : sata_mv
[   10.155891] ata1: SATA max UDMA/133 irq 21
[   10.160006] ata2: SATA max UDMA/133 irq 21
[   10.664944] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[   10.685017] ata1.00: ATA-8: ST1000DM003-9YN162, HP13, max UDMA/100
[   10.691221] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 
31/32)
[   10.735008] ata1.00: configured for UDMA/100
[   10.739541] scsi 0:0:0:0: Direct-Access     ATA      ST1000DM003-9YN1 
HP13 PQ: 0 ANSI: 5
[   11.254943] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[   11.275014] ata2.00: ATA-8: ST1000DM003-9YN162, HP13, max UDMA/100
[   11.281215] ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 
31/32)
[   11.325008] ata2.00: configured for UDMA/100
[   11.329512] scsi 1:0:0:0: Direct-Access     ATA      ST1000DM003-9YN1 
HP13 PQ: 0 ANSI: 5
[   11.359621] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: 
(1.00 TB/931 GiB)
[   11.367334] sd 0:0:0:0: [sda] 4096-byte physical blocks
[   11.372913] sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: 
(1.00 TB/931 GiB)
[   11.380613] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[   11.392519] sd 0:0:0:0: [sda] Write Protect is off
[   11.397463] sd 1:0:0:0: [sdb] Write Protect is off
[   11.402369] sd 0:0:0:0: [sda] Write cache: enabled, read cache: 
enabled, doesn't support DPO or FUA
[   11.411500] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: 
enabled, doesn't support DPO or FUA
[   11.436363]  sda: sda1 sda2
[   11.441669] sd 0:0:0:0: [sda] Attached SCSI disk
[   11.462918]  sdb: sdb1 sdb2
[   11.468303] sd 1:0:0:0: [sdb] Attached SCSI disk
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top 
... Begin: Assembling all MD arrays ... [   11.751288] md: md0 stopped.
[   11.761494] md: bind<sdb1>
[   11.770159] md: bind<sda1>
[   11.784403] md: raid0 personality registered for level 0
[   11.790303] bio: create slab <bio-1> at 1
[   11.794349] md/raid0:md0: md_size is 1992704 sectors.
[   11.799437] md: RAID0 configuration for md0 - 1 zone
[   11.804413] md: zone0=[sda1/sdb1]
[   11.807772]       zone-offset=         0KB, device-offset=         
0KB, size=    996352KB
[   11.815982]
[   11.817501] md0: detected capacity change from 0 to 1020264448
mdadm: /dev/md/0 has been started with 2 drives.[   11.827592]  md0: 
unknown partition table

[   12.076837] md: md1 stopped.
[   12.086500] md: bind<sdb2>
[   12.102464] md: bind<sda2>
[   12.110375] md: raid1 personality registered for level 1
[   12.116386] md/raid1:md1: active with 2 out of 2 mirrors
[   12.121783] md1: detected capacity change from 0 to 999558021120
mdadm: /dev/md/1 has been started with 2 drives.
[   12.135973]  md1: unknown partition table
Success: assembled all arrays.
done.
[   12.341372] device-mapper: uevent: version 1.0.3
[   12.347248] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) 
initialised: dm-devel@redhat.com
  Volume group "VG01" not found
  Skipping volume group VG01
Unable to find LVM volume VG01/LVG01
Unlocking the disk 
/dev/disk/by-uuid/bd88fd91-a823-4657-945c-cfec66b95a74 (md1_crypt)
Enter passphrase:
  Reading all physical volumes.  This may take a while...
  Found volume group "VG01" using metadata type lvm2
  2 logical volume(s) in volume group "VG01" now active
cryptsetup: md1_crypt set up successfully
done.
Begin: Running /scripts/local-premount ... done.
[   18.721597] EXT4-fs (dm-1): mounted filesystem with ordered data 
mode. Opts: (null)
Begin: Running /scripts/local-bottom ... done.
done.
Begin: Running /scripts/init-bottom ... evdev: Error opening 
/dev/input/by-path/platform-gpio-keys-event: No such file or directory
register() - Error loading module
done.

INIT: version 2.88 booting

[info] Using makefile-style concurrent boot in runlevel S.
[....] Starting the hotplug events dispatcher: udevd[   20.318076] 
udevd[356]: starting version 175
[ ok .
[....] Synthesizing the initial hotplug events...[ ok done.
[   20.871973] input: gpio-keys as 
/devices/platform/gpio-keys/input/input0
[....] Waiting for /dev to be fully populated...[   21.015831] usbcore: 
registered new interface driver usbfs
[   21.025017] ahci 0000:00:01.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 
0x3 impl SATA mode
[   21.033145] ahci 0000:00:01.0: flags: 64bit ncq pm led clo pmp pio 
slum part
[   21.044993] usbcore: registered new interface driver hub
[   21.053767] usbcore: registered new device driver usb
[   21.084546] scsi2 : ahci
[   21.094051] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) 
Driver
[   21.100670] scsi3 : ahci
[   21.103657] ata3: SATA max UDMA/133 abar m8192@0xe0010000 port 
0xe0010100 irq 9
[   21.111015] ata4: SATA max UDMA/133 abar m8192@0xe0010000 port 
0xe0010180 irq 9
[   21.130133] xhci_hcd 0000:01:01.0: xHCI Host Controller
[   21.144819] xhci_hcd 0000:01:01.0: new USB bus registered, assigned 
bus number 1
[   21.165097] usb usb1: New USB device found, idVendor=1d6b, 
idProduct=0002
[   21.171971] usb usb1: New USB device strings: Mfr=3, Product=2, 
SerialNumber=1
[   21.179235] usb usb1: Product: xHCI Host Controller
[   21.184129] usb usb1: Manufacturer: Linux 3.2.0-4-kirkwood xhci_hcd
[   21.190451] usb usb1: SerialNumber: 0000:01:01.0
[   21.196188] hub 1-0:1.0: USB hub found
[   21.199960] hub 1-0:1.0: 2 ports detected
[   21.204134] xhci_hcd 0000:01:01.0: xHCI Host Controller
[   21.217310] xhci_hcd 0000:01:01.0: new USB bus registered, assigned 
bus number 2
[   21.243550] usb usb2: New USB device found, idVendor=1d6b, 
idProduct=0003
[   21.250440] usb usb2: New USB device strings: Mfr=3, Product=2, 
SerialNumber=1
[   21.257726] usb usb2: Product: xHCI Host Controller
[   21.262618] usb usb2: Manufacturer: Linux 3.2.0-4-kirkwood xhci_hcd
[   21.268913] usb usb2: SerialNumber: 0000:01:01.0
[   21.275468] hub 2-0:1.0: USB hub found
[   21.279427] hub 2-0:1.0: 2 ports detected
[   21.464955] ata4: SATA link down (SStatus 0 SControl 300)
[   21.470435] ata3: SATA link down (SStatus 0 SControl 300)
[   21.521235] orion-ehci orion-ehci.0: Marvell Orion EHCI
[   21.527525] orion-ehci orion-ehci.0: new USB bus registered, assigned 
bus number 3
[   21.564951] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[   21.584933] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[   21.590919] usb usb3: New USB device found, idVendor=1d6b, 
idProduct=0002
[   21.597749] usb usb3: New USB device strings: Mfr=3, Product=2, 
SerialNumber=1
[   21.605008] usb usb3: Product: Marvell Orion EHCI
[   21.609726] usb usb3: Manufacturer: Linux 3.2.0-4-kirkwood ehci_hcd
[   21.616019] usb usb3: SerialNumber: orion-ehci.0
[   21.621297] hub 3-0:1.0: USB hub found
[   21.625091] hub 3-0:1.0: 1 port detected
[   21.629191] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 
1.4
[   21.645458] mv643xx_eth smi: probed
[   21.655550] mv643xx_eth_port mv643xx_eth_port.0: eth0: port 0 with 
MAC address 00:08:9b:cd:08:be
[ ok done.
[....] Generating udev events for MD arrays...[ ok done.
[   22.408039] EXT4-fs (dm-1): re-mounted. Opts: (null)
[....] Checking root file system...fsck from util-linux 2.20.1
/dev/mapper/VG01-LVG01: clean, 26279/3662848 files, 414837/14648320 
blocks
[ ok done.
[   22.826543] EXT4-fs (dm-1): re-mounted. Opts: errors=remount-ro
[....] Cleaning up temporary files... /tmp[ ok .
[....] Starting early crypto disks...[info] md0_crypt (starting)...
md0_crypt (started)...md1_crypt (running)...[ ok done.
[   24.068475] loop: module loaded
[info] Loading kernel module gpio_keys.
[info] Loading kernel module loop.
[....] Setting up LVM Volume Groups...[ ok done.
[....] Starting remaining crypto disks...md0_crypt (running)...md1_crypt 
(running)...[ ok done.
[....] Activating lvm and md swap...[   25.836712] Adding 996348k swap 
on /dev/mapper/md0_crypt.  Priority:-1 extents:1 across:996348k
[ ok done.
[....] Checking file systems...fsck from util-linux 2.20.1
/dev/mapper/VG01-LVG02: clean, 22/48832512 files, 3115544/195312640 
blocks
[ ok done.
[....] Mounting local filesystems...[   26.815291] EXT4-fs (dm-2): 
mounted filesystem with ordered data mode. Opts: (null)
[ ok done.
[....] Activating swapfile swap...[ ok done.
[....] Cleaning up temporary files...[ ok .
[....] Setting kernel variables ...[ ok done.
[....] Configuring network interfaces...[ ok done.
[   28.156761] NET: Registered protocol family 10
[....] Starting rpcbind daemon...[   28.585602] ADDRCONF(NETDEV_UP): 
eth0: link is not ready
[ ok .
[....] Starting NFS common utilities: statd[   28.845299] RPC: 
Registered named UNIX socket transport module.
[   28.851249] RPC: Registered udp transport module.
[   28.855984] RPC: Registered tcp transport module.
[   28.860701] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   28.909240] FS-Cache: Loaded
[   29.013219] FS-Cache: Netfs 'nfs' registered for caching
[   29.060307] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
 idmapd[ ok .
[....] Cleaning up temporary files...[ ok .
[....] Starting qcontrol daemon: qcontrol[ ok .

INIT: Entering runlevel: 2

[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting rpcbind daemon...[....] Already running.[ ok .
[....] Starting NFS common utilities: statd idmapd[ ok .
[....] Starting enhanced syslogd: rsyslogd[ ok .
[....] Starting deferred execution scheduler: atd[ ok .
[....] Starting periodic command scheduler: cron[ ok .
[....] Starting MTA: exim4[ ok .
[....] Starting MD monitoring service: mdadm --monitor[   31.704903] 
mv643xx_eth_port mv643xx_eth_port.0: eth0: link up, 1000 Mb/s, full 
duplex, flow control disabled
[   31.715112] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ ok .
[....] Starting OpenBSD Secure Shell server: sshd[ ok .
[info] System boot completed.

Debian GNU/Linux 7 NAS ttyS0

NAS login: root

Password:
Last login: Sun Sep  7 18:32:31 EDT 2014 on ttyS0
Linux NAS 3.2.0-4-kirkwood #1 Debian 3.2.60-1+deb7u3 armv5tel

The programs included with the Debian GNU/Linux system are free 
software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.

Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
root@NAS:~#