Re: Re: Comment repare un probleme de disque dur
Le 20/10/2015 20:46, Pascal Hambourg a écrit :
> smartctl (paquet smartmontools) permet d'accéder au diagnostic SMART
> d'un disque.
> badblocks permet de rechercher les secteurs défectueux d'un disque ou
> d'une partition.
>
> Concernant le marquage et la réparation des secteurs défectueux, il y a
> deux types différents.
> - Ceux effectués par le disque de façon plus ou moins transparente. La
> "réparation" se fait par réallocation avec un secteur de réserve (s'il
> en reste) lors de l'écriture d'un secteur précédemment détecté comme
> illisible.
+1 pour l'outil smartctl
Mon disque est mort et je n'avais jamais suivi correctement sa vie
hachée, en fait smartctl m'aurait montré que d'accidents en plantages,
le contrôleur de disque, ré-allouait automatiquement des secteurs sains
pour remplacer les défectueux, jusqu'à épuisement de ses réserves.
Voir ci-dessous pour illustration mais attention la trace ci-dessous est
pour mon nouveau disque SSD qui n'est pas "smartctl" ;-)
Tu regardes bien le diag de ton sda, et tu verras si ton disque est mort
(plus de réserve) ou s'il peut être réparé
└─[#]> sudo smartctl -a /dev/sda
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.13.0-66-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: Samsung SSD 840 EVO 500GB
Serial Number: S1DHNSAF325931T
LU WWN Device Id: 5 002538 8a03165ba
Firmware Version: EXT0BB6Q
User Capacity: 500 107 862 016 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 1.5 Gb/s)
Local Time is: Wed Oct 21 08:48:50 2015 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 6600) seconds.
Offline data collection
capabilities: (0x53) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 110) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 1590
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 338
177 Wear_Leveling_Count 0x0013 100 100 000 Pre-fail Always - 0
179 Used_Rsvd_Blk_Cnt_Tot 0x0013 100 100 010 Pre-fail Always - 0
181 Program_Fail_Cnt_Total 0x0032 100 100 010 Old_age Always - 0
182 Erase_Fail_Count_Total 0x0032 100 100 010 Old_age Always - 0
183 Runtime_Bad_Block 0x0013 100 100 010 Pre-fail Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0032 064 048 000 Old_age Always - 36
195 Hardware_ECC_Recovered 0x001a 200 200 000 Old_age Always - 0
199 UDMA_CRC_Error_Count 0x003e 100 100 000 Old_age Always - 0
235 Unknown_Attribute 0x0012 099 099 000 Old_age Always - 13
241 Total_LBAs_Written 0x0032 099 099 000 Old_age Always - 1455073856
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
--
Pro. Signature
Pierre Touzeau
-----------------------------------------------------------
Chargé de mission Préfecture de region Basse-Normandie
SGAR, rue Daniel HUET 14038 CAEN CEDEX +33 231 306 306
pierre.touzeau@basse-normandie.pref.gouv.fr +33 608 968 574
-----------------------------------------------------------
Reply to: