Package: src:linux Version: 3.2.35-2 Severity: important Hi everybody, I'm rather clueless on this error. Grub refuses to boot the current Wheezy kernel on this box. The message is "cannot read the linux header". 3.2.0-3-amd64 boots without problems. I reinstalled the kernel package as well as grub-pc and ran update-grub without problems. "debsums -sa" does not report any modified files for the kernel package or any grub package installed. So I'm a bit clueless. The box is an rather old Intel Core2 6300 box. Could that be the problem? Could this kernel be incompatible with the processor? Cheers, Christopher -- Package-specific info: ** Kernel log: boot messages should be attached ** Model information sys_vendor: product_name: product_version: chassis_vendor: chassis_version: bios_vendor: Intel Corp. bios_version: MQ96510J.86A.1458.2006.1017.1151 board_vendor: Intel Corporation board_name: DG965MQ board_version: AAD37419-302 ** PCI devices: 00:00.0 Host bridge [0600]: Intel Corporation 82P965/G965 Memory Controller Hub [8086:29a0] (rev 02) Subsystem: Intel Corporation Device [8086:514d] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel driver in use: agpgart-intel 00:01.0 PCI bridge [0604]: Intel Corporation 82P965/G965 PCI Express Root Port [8086:29a1] (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 Memory behind bridge: e0500000-e05fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:02.0 VGA compatible controller [0300]: Intel Corporation 82G965 Integrated Graphics Controller [8086:29a2] (rev 02) (prog-if 00 [VGA controller]) Subsystem: Intel Corporation Device [8086:514d] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 48 Region 0: Memory at e0300000 (32-bit, non-prefetchable) [size=1M] Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M] Region 4: I/O ports at 2110 [size=8] Expansion ROM at <unassigned> [disabled] Capabilities: <access denied> Kernel driver in use: i915 00:02.1 Display controller [0380]: Intel Corporation 82G965 Integrated Graphics Controller [8086:29a3] (rev 02) Subsystem: Intel Corporation Device [8086:514d] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Region 0: Memory at e0200000 (32-bit, non-prefetchable) [size=1M] Capabilities: <access denied> 00:03.0 Communication controller [0780]: Intel Corporation 82P965/G965 HECI Controller [8086:29a4] (rev 02) Subsystem: Intel Corporation Device [8086:514d] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 11 Region 0: Memory at e0426100 (64-bit, non-prefetchable) [size=16] Capabilities: <access denied> 00:19.0 Ethernet controller [0200]: Intel Corporation 82566DC Gigabit Network Connection [8086:104b] (rev 02) Subsystem: Intel Corporation Device [8086:0001] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 46 Region 0: Memory at e0400000 (32-bit, non-prefetchable) [size=128K] Region 1: Memory at e0424000 (32-bit, non-prefetchable) [size=4K] Region 2: I/O ports at 20e0 [size=32] Capabilities: <access denied> Kernel driver in use: e1000e 00:1a.0 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 [8086:2834] (rev 02) (prog-if 00 [UHCI]) Subsystem: Intel Corporation Device [8086:514d] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 4: I/O ports at 20c0 [size=32] Kernel driver in use: uhci_hcd 00:1a.1 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 [8086:2835] (rev 02) (prog-if 00 [UHCI]) Subsystem: Intel Corporation Device [8086:514d] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 21 Region 4: I/O ports at 20a0 [size=32] Kernel driver in use: uhci_hcd 00:1a.7 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 [8086:283a] (rev 02) (prog-if 20 [EHCI]) Subsystem: Intel Corporation Device [8086:514d] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 0: Memory at e0425c00 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1b.0 Audio device [0403]: Intel Corporation 82801H (ICH8 Family) HD Audio Controller [8086:284b] (rev 02) Subsystem: Intel Corporation Device [8086:2501] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 49 Region 0: Memory at e0420000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel 00:1c.0 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 [8086:283f] (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 00006000-00006fff Memory behind bridge: e0600000-e06fffff Prefetchable memory behind bridge: 00000000e1200000-00000000e13fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1c.1 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 [8086:2841] (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 I/O behind bridge: 00001000-00001fff Memory behind bridge: e0100000-e01fffff Prefetchable memory behind bridge: 00000000e1000000-00000000e11fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1c.2 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 3 [8086:2843] (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 I/O behind bridge: 00005000-00005fff Memory behind bridge: e0700000-e07fffff Prefetchable memory behind bridge: 00000000e0e00000-00000000e0ffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1c.3 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 4 [8086:2845] (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=05, subordinate=05, sec-latency=0 I/O behind bridge: 00004000-00004fff Memory behind bridge: e0800000-e08fffff Prefetchable memory behind bridge: 00000000e0c00000-00000000e0dfffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1c.4 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5 [8086:2847] (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=06, subordinate=06, sec-latency=0 I/O behind bridge: 00003000-00003fff Memory behind bridge: e0900000-e09fffff Prefetchable memory behind bridge: 00000000e0a00000-00000000e0bfffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1d.0 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 [8086:2830] (rev 02) (prog-if 00 [UHCI]) Subsystem: Intel Corporation Device [8086:514d] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 4: I/O ports at 2080 [size=32] Kernel driver in use: uhci_hcd 00:1d.1 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 [8086:2831] (rev 02) (prog-if 00 [UHCI]) Subsystem: Intel Corporation Device [8086:514d] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 4: I/O ports at 2060 [size=32] Kernel driver in use: uhci_hcd 00:1d.2 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 [8086:2832] (rev 02) (prog-if 00 [UHCI]) Subsystem: Intel Corporation Device [8086:514d] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at 2040 [size=32] Kernel driver in use: uhci_hcd 00:1d.7 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 [8086:2836] (rev 02) (prog-if 20 [EHCI]) Subsystem: Intel Corporation Device [8086:514d] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 0: Memory at e0425800 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev f2) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=07, subordinate=07, sec-latency=32 Memory behind bridge: e0000000-e00fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 00:1f.0 ISA bridge [0601]: Intel Corporation 82801HH (ICH8DH) LPC Interface Controller [8086:2812] (rev 02) Subsystem: Intel Corporation Device [8086:514d] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> 00:1f.2 SATA controller [0106]: Intel Corporation 82801HR/HO/HH (ICH8R/DO/DH) 6 port SATA Controller [AHCI mode] [8086:2821] (rev 02) (prog-if 01 [AHCI 1.0]) Subsystem: Intel Corporation Device [8086:514d] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 47 Region 0: I/O ports at 2108 [size=8] Region 1: I/O ports at 211c [size=4] Region 2: I/O ports at 2100 [size=8] Region 3: I/O ports at 2118 [size=4] Region 4: I/O ports at 2020 [size=32] Region 5: Memory at e0425000 (32-bit, non-prefetchable) [size=2K] Capabilities: <access denied> Kernel driver in use: ahci 00:1f.3 SMBus [0c05]: Intel Corporation 82801H (ICH8 Family) SMBus Controller [8086:283e] (rev 02) Subsystem: Intel Corporation Device [8086:514d] Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin B routed to IRQ 21 Region 0: Memory at e0426000 (32-bit, non-prefetchable) [size=256] Region 4: I/O ports at 2000 [size=32] Kernel driver in use: i801_smbus 03:00.0 IDE interface [0101]: Marvell Technology Group Ltd. 88SE6101/6102 single-port PATA133 interface [11ab:6101] (rev b1) (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: Marvell Technology Group Ltd. 88SE6101/6102 single-port PATA133 interface [11ab:6101] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 17 Region 0: I/O ports at 1018 [size=8] Region 1: I/O ports at 1024 [size=4] Region 2: I/O ports at 1010 [size=8] Region 3: I/O ports at 1020 [size=4] Region 4: I/O ports at 1000 [size=16] Region 5: Memory at e0100000 (32-bit, non-prefetchable) [size=512] Capabilities: <access denied> Kernel driver in use: pata_marvell 07:03.0 FireWire (IEEE 1394) [0c00]: Texas Instruments TSB43AB22A IEEE-1394a-2000 Controller (PHY/Link) [iOHCI-Lynx] [104c:8023] (prog-if 10 [OHCI]) Subsystem: Intel Corporation Device [8086:514d] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (500ns min, 1000ns max), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 19 Region 0: Memory at e0004000 (32-bit, non-prefetchable) [size=2K] Region 1: Memory at e0000000 (32-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: firewire_ohci ** USB devices: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 0409:005a NEC Corp. HighSpeed Hub Bus 002 Device 003: ID 0557:2213 ATEN International Co., Ltd CS682 2-Port USB 2.0 DVI KVM Switch -- System Information: Debian Release: 7.0 APT prefers testing APT policy: (500, 'testing'), (500, 'stable'), (300, 'proposed-updates') Architecture: amd64 (x86_64) Foreign Architectures: i386 Kernel: Linux 3.2.0-3-amd64 (SMP w/2 CPU cores) Locale: LANG=de_DE@euro, LC_CTYPE=de_DE@euro (charmap=ISO-8859-15) Shell: /bin/sh linked to /bin/dash Versions of packages linux-image-3.2.0-4-amd64 depends on: ii debconf [debconf-2.0] 1.5.49 ii initramfs-tools [linux-initramfs-tool] 0.109 ii kmod 9-2 ii linux-base 3.5 ii module-init-tools 9-2 Versions of packages linux-image-3.2.0-4-amd64 recommends: pn firmware-linux-free <none> Versions of packages linux-image-3.2.0-4-amd64 suggests: pn debian-kernel-handbook <none> ii grub-pc 1.99-26 pn linux-doc-3.2 <none> Versions of packages linux-image-3.2.0-4-amd64 is related to: pn firmware-atheros <none> pn firmware-bnx2 <none> pn firmware-bnx2x <none> pn firmware-brcm80211 <none> pn firmware-intelwimax <none> pn firmware-ipw2x00 <none> pn firmware-ivtv <none> pn firmware-iwlwifi <none> pn firmware-libertas <none> pn firmware-linux <none> pn firmware-linux-nonfree <none> pn firmware-myricom <none> pn firmware-netxen <none> pn firmware-qlogic <none> pn firmware-ralink <none> pn firmware-realtek <none> pn xen-hypervisor <none> -- debconf information: linux-image-3.2.0-4-amd64/postinst/depmod-error-initrd-3.2.0-4-amd64: false linux-image-3.2.0-4-amd64/prerm/removing-running-kernel-3.2.0-4-amd64: true linux-image-3.2.0-4-amd64/postinst/ignoring-ramdisk: linux-image-3.2.0-4-amd64/postinst/missing-firmware-3.2.0-4-amd64:
#
# DO NOT EDIT THIS FILE
#
# It is automatically generated by grub-mkconfig using templates
# from /etc/grub.d and settings from /etc/default/grub
#
### BEGIN /etc/grub.d/00_header ###
if [ -s $prefix/grubenv ]; then
load_env
fi
set default="0"
if [ "${prev_saved_entry}" ]; then
set saved_entry="${prev_saved_entry}"
save_env saved_entry
set prev_saved_entry=
save_env prev_saved_entry
set boot_once=true
fi
function savedefault {
if [ -z "${boot_once}" ]; then
saved_entry="${chosen}"
save_env saved_entry
fi
}
function load_video {
insmod vbe
insmod vga
insmod video_bochs
insmod video_cirrus
}
serial
insmod part_msdos
insmod xfs
set root='(hd0,msdos2)'
search --no-floppy --fs-uuid --set=root 8819153f-2138-4c79-b1b9-feb823c00b00
if loadfont /usr/share/grub/unicode.pf2 ; then
set gfxmode=1280x1024
load_video
insmod gfxterm
fi
terminal_input gfxterm console serial
terminal_output gfxterm console serial
set timeout=5
### END /etc/grub.d/00_header ###
### BEGIN /etc/grub.d/05_debian_theme ###
set menu_color_normal=cyan/blue
set menu_color_highlight=white/blue
### END /etc/grub.d/05_debian_theme ###
### BEGIN /etc/grub.d/10_linux ###
menuentry 'Debian GNU/Linux, with Linux 3.2.0-4-amd64' --class debian --class gnu-linux --class gnu --class os {
insmod gzio
insmod part_msdos
insmod xfs
set root='(hd0,msdos2)'
search --no-floppy --fs-uuid --set=root 8819153f-2138-4c79-b1b9-feb823c00b00
echo 'Loading Linux 3.2.0-4-amd64 ...'
linux /boot/vmlinuz-3.2.0-4-amd64 root=UUID=8819153f-2138-4c79-b1b9-feb823c00b00 ro quiet
echo 'Loading initial ramdisk ...'
initrd /boot/initrd.img-3.2.0-4-amd64
}
menuentry 'Debian GNU/Linux, with Linux 3.2.0-4-amd64 (recovery mode)' --class debian --class gnu-linux --class gnu --class os {
insmod gzio
insmod part_msdos
insmod xfs
set root='(hd0,msdos2)'
search --no-floppy --fs-uuid --set=root 8819153f-2138-4c79-b1b9-feb823c00b00
echo 'Loading Linux 3.2.0-4-amd64 ...'
linux /boot/vmlinuz-3.2.0-4-amd64 root=UUID=8819153f-2138-4c79-b1b9-feb823c00b00 ro single
echo 'Loading initial ramdisk ...'
initrd /boot/initrd.img-3.2.0-4-amd64
}
menuentry 'Debian GNU/Linux, with Linux 3.2.0-3-amd64' --class debian --class gnu-linux --class gnu --class os {
insmod gzio
insmod part_msdos
insmod xfs
set root='(hd0,msdos2)'
search --no-floppy --fs-uuid --set=root 8819153f-2138-4c79-b1b9-feb823c00b00
echo 'Loading Linux 3.2.0-3-amd64 ...'
linux /boot/vmlinuz-3.2.0-3-amd64 root=UUID=8819153f-2138-4c79-b1b9-feb823c00b00 ro quiet
echo 'Loading initial ramdisk ...'
initrd /boot/initrd.img-3.2.0-3-amd64
}
menuentry 'Debian GNU/Linux, with Linux 3.2.0-3-amd64 (recovery mode)' --class debian --class gnu-linux --class gnu --class os {
insmod gzio
insmod part_msdos
insmod xfs
set root='(hd0,msdos2)'
search --no-floppy --fs-uuid --set=root 8819153f-2138-4c79-b1b9-feb823c00b00
echo 'Loading Linux 3.2.0-3-amd64 ...'
linux /boot/vmlinuz-3.2.0-3-amd64 root=UUID=8819153f-2138-4c79-b1b9-feb823c00b00 ro single
echo 'Loading initial ramdisk ...'
initrd /boot/initrd.img-3.2.0-3-amd64
}
menuentry 'Debian GNU/Linux, with Linux 3.2.0-2-amd64' --class debian --class gnu-linux --class gnu --class os {
insmod gzio
insmod part_msdos
insmod xfs
set root='(hd0,msdos2)'
search --no-floppy --fs-uuid --set=root 8819153f-2138-4c79-b1b9-feb823c00b00
echo 'Loading Linux 3.2.0-2-amd64 ...'
linux /boot/vmlinuz-3.2.0-2-amd64 root=UUID=8819153f-2138-4c79-b1b9-feb823c00b00 ro quiet
echo 'Loading initial ramdisk ...'
initrd /boot/initrd.img-3.2.0-2-amd64
}
menuentry 'Debian GNU/Linux, with Linux 3.2.0-2-amd64 (recovery mode)' --class debian --class gnu-linux --class gnu --class os {
insmod gzio
insmod part_msdos
insmod xfs
set root='(hd0,msdos2)'
search --no-floppy --fs-uuid --set=root 8819153f-2138-4c79-b1b9-feb823c00b00
echo 'Loading Linux 3.2.0-2-amd64 ...'
linux /boot/vmlinuz-3.2.0-2-amd64 root=UUID=8819153f-2138-4c79-b1b9-feb823c00b00 ro single
echo 'Loading initial ramdisk ...'
initrd /boot/initrd.img-3.2.0-2-amd64
}
menuentry 'Debian GNU/Linux, with Linux 2.6.32-5-amd64' --class debian --class gnu-linux --class gnu --class os {
insmod gzio
insmod part_msdos
insmod xfs
set root='(hd0,msdos2)'
search --no-floppy --fs-uuid --set=root 8819153f-2138-4c79-b1b9-feb823c00b00
echo 'Loading Linux 2.6.32-5-amd64 ...'
linux /boot/vmlinuz-2.6.32-5-amd64 root=UUID=8819153f-2138-4c79-b1b9-feb823c00b00 ro quiet
echo 'Loading initial ramdisk ...'
initrd /boot/initrd.img-2.6.32-5-amd64
}
menuentry 'Debian GNU/Linux, with Linux 2.6.32-5-amd64 (recovery mode)' --class debian --class gnu-linux --class gnu --class os {
insmod gzio
insmod part_msdos
insmod xfs
set root='(hd0,msdos2)'
search --no-floppy --fs-uuid --set=root 8819153f-2138-4c79-b1b9-feb823c00b00
echo 'Loading Linux 2.6.32-5-amd64 ...'
linux /boot/vmlinuz-2.6.32-5-amd64 root=UUID=8819153f-2138-4c79-b1b9-feb823c00b00 ro single
echo 'Loading initial ramdisk ...'
initrd /boot/initrd.img-2.6.32-5-amd64
}
### END /etc/grub.d/10_linux ###
### BEGIN /etc/grub.d/20_linux_xen ###
### END /etc/grub.d/20_linux_xen ###
### BEGIN /etc/grub.d/20_memtest86+ ###
menuentry "Memory test (memtest86+)" {
insmod part_msdos
insmod xfs
set root='(hd0,msdos2)'
search --no-floppy --fs-uuid --set=root 8819153f-2138-4c79-b1b9-feb823c00b00
linux16 /boot/memtest86+.bin
}
menuentry "Memory test (memtest86+, serial console 115200)" {
insmod part_msdos
insmod xfs
set root='(hd0,msdos2)'
search --no-floppy --fs-uuid --set=root 8819153f-2138-4c79-b1b9-feb823c00b00
linux16 /boot/memtest86+.bin console=ttyS0,115200n8
}
menuentry "Memory test (memtest86+, experimental multiboot)" {
insmod part_msdos
insmod xfs
set root='(hd0,msdos2)'
search --no-floppy --fs-uuid --set=root 8819153f-2138-4c79-b1b9-feb823c00b00
multiboot /boot/memtest86+_multiboot.bin
}
menuentry "Memory test (memtest86+, serial console 115200, experimental multiboot)" {
insmod part_msdos
insmod xfs
set root='(hd0,msdos2)'
search --no-floppy --fs-uuid --set=root 8819153f-2138-4c79-b1b9-feb823c00b00
multiboot /boot/memtest86+_multiboot.bin console=ttyS0,115200n8
}
### END /etc/grub.d/20_memtest86+ ###
### BEGIN /etc/grub.d/30_os-prober ###
### END /etc/grub.d/30_os-prober ###
### BEGIN /etc/grub.d/40_custom ###
# This file provides an easy way to add custom menu entries. Simply type the
# menu entries you want to add after this comment. Be careful not to change
# the 'exec tail' line above.
### END /etc/grub.d/40_custom ###
### BEGIN /etc/grub.d/41_custom ###
if [ -f $prefix/custom.cfg ]; then
source $prefix/custom.cfg;
fi
### END /etc/grub.d/41_custom ###
Attachment:
cpuinfo
Description: inode/empty